H-Beams and Structural Steel: When a Growing Yard Needs 315 Tons

Most yards hit the same wall at roughly the same stage. The small shear that carried the business for the first few years still works, but the material has changed. Thicker plate shows up. H-beams arrive more often. Intake climbs past what one machine can clear in a shift. The owner starts to think about a second shift, a second machine, or something bigger. For many of those yards the next step is a 315 ton gantry shear, rated for 30 mm plate and 25 to 45 tons a day. When sizing hydraulic scrap shear equipment for continuous duty, the same logic applies across the range: frame rigidity, cycle speed and operating cost move together.

HUAXIN hydraulic gantry scrap shear under full-load inspection at the Tangshan factory
A HUAXIN hydraulic gantry shear during full-load hydraulic pressure and blade clearance inspection at our Tangshan factory.

That is the buyer our 315-ton hydraulic gantry shear is built for. This article looks at what it cuts, what it replaces, and how to tell whether it fits your yard or whether a smaller or larger machine makes more sense.

The mid-tonnage position

The 315 ton machine sits between our 200 ton gantry shear and the heavier 400 and 500 ton classes. It is aimed at mixed ferrous intake climbing past 30 tons a day, plate arriving in thicker sizes, and a second shift on the horizon.

Daily output runs from 25 to 45 tons on a 10-hour day, depending on material, loading efficiency and cut length. The typical buyer is an independent scrap yard taking in 30 to 40 tons of mixed ferrous a day. Demolition contractors processing structural salvage buy it too. So do small steel mills and foundries handling their own offcuts and returns.

Key figures

Item Q91-315
Shearing force 315 t (3,150 kN)
Blade length 1,200 mm or 1,300 mm
Motor power 37 to 45 kW (2×22 kW option)
Cycle time 20 to 35 seconds per cut
Output 2.5 to 4.5 t/h, 25 to 45 t/day (10-hour day), material-dependent.
Max plate (continuous, mild steel) 30 mm
Feed box length 4.5 m or 5 m
Power source Electric, generator or diesel
Blades M6V, H13, X45 or D2 tool steel, four-edge reversible.
Control PLC auto cycle, remote control, emergency stop
Certification CE / ISO 9001

What a 315 ton scrap metal shear cuts

The machine is rated for continuous cutting of mild steel plate up to 30 mm. Beyond plate, it handles:

  • Rebar, loose or bundled.
  • H-beams and I-beams in light and medium sections.
  • Steel pipe, bundled or single, within wall-thickness limits.
  • Light steel structures such as angle, channel and profile scrap.
  • General mixed ferrous scrap and demolition salvage.

One boundary deserves attention. HMS 1 and 2 goes through only occasionally, in controlled quantities. This is a mixed-ferrous machine. If heavy HMS at full section thickness is your daily routine, look at a gantry in the 500 ton class or above. Our engineers give the same advice on every inquiry.

Cutting H-beams and structural steel

The 315 is a guillotine-type gantry shear. An excavator or grapple loads material into the feed box. A hydraulic pushing cylinder advances it to a preset position. A hold-down cylinder clamps it, and the blade descends, cuts and retracts in 20 to 35 seconds.

For beams, a few practical points help.

  • Choose the blade length by your longest regular section. A 1,200 mm blade suits compact yards and shorter stock, while 1,300 mm fits intake with longer beams and bundled sections.
  • Use PLC presets. Material-specific presets turn a switch between plate, profile and mixed scrap into a button press instead of an operator recalculation.
  • Be realistic about “light and medium.” Heavy H-beam sections call for a higher-capacity model, usually the 400 ton class.
  • Plan for the slow end of the cycle. Beams and thick sections tend to sit near 35 seconds, not 20.

One shear instead of two

Much of the demand for this class comes from consolidation. A yard running two small shears pays twice the labour, twice the maintenance attention and twice the floor space. It still struggles with heavier material.

One 315 ton shear can often replace both, run with a single operator, and clear plate and beam stock that 200-ton machines can only nibble at. That will not hold for every yard. If your two small machines run different materials at the same time, keeping both may suit you better. If both are bottlenecked on the same stream, consolidation deserves a hard look.

Where it is not the right choice

If daily intake is still under about 20 tons of light material, the 200 ton machine is the better fit. If your beams are heavy or plate runs past 30 mm every day, move up. A simple guide:

Your material profile Better machine
Light scrap, rebar and profile, plate to 25 mm, 20 to 45 t/day 200 ton class
30 mm plate continuously, mixed ferrous, light and medium beams, 25 to 45 t/day 315 ton class
Heavier H-beams, 40 mm plate, 35 to 55 t/day 400 ton class
Heavy structural and continuous HMS, 60 to 80 t/day 630 ton class and above

If you are weighing these options, the 315 versus 200 and 400 ton comparison walks through the boundaries in more detail.

Blades: the published life, and how to use it

One complete blade set processes roughly 5,000 to 10,000 tons of scrap before replacement, depending on material and thickness. Each blade has four cutting edges, so rotation stretches that life before a new set is needed. Spare blades ship by DHL or FedEx.

Treat the range as a guide, not a promise. A yard cutting clean structural steel will sit near one end. A yard cutting abrasive demolition material will sit near the other. Record your own numbers across the first few sets and plan stock from them. Even with express shipping, keep a spare set on site, because transit time is still downtime.

Power options

The machine can be built for 230 V, 380 V, 400 V, 415 V, 440 V or 480 V input at 50 or 60 Hz, with electric motor, generator or diesel drive. Mid-size yards upgrading from smaller equipment often find their incoming supply needs adjusting.

Take that seriously. The standard drive is 37 to 45 kW for grid-connected yards at the upper end of the 25 to 45 ton band. A 2×22 kW option suits generator use or tighter incoming capacity. As a rule of thumb, a 37 kW drive needs at least a 53 kVA transformer and a 45 kW drive needs 63 kVA. Send us your power details before the machine is built, and we will specify the right package. Our article on diesel versus electric machines covers off-grid options.

Feed box and workflow

The feed box comes in 4.5 m or 5 m. Longer staging means fewer excavator cycles and smoother continuous cutting at higher tonnages. Both lengths use the same hydraulic pushing system and PLC presets.

Plan the workflow around the box before the machine arrives. Decide where the excavator or grapple stands, where cut pieces drop, and how trucks reach them. A good shear in a bad layout will underperform. Our recycling line design article explains how to plan this.

Support, shipping and warranty

Each machine is built to order, with lead time, packing and shipping terms confirmed in the quotation. Every shear is load-tested at the factory before shipment. Standard commissioning support is remote: installation guidance videos, wiring and hydraulic checklists, video-call startup walkthroughs and crew training. On-site installation by our engineers can be quoted where the project needs it.

The standard warranty is 12 months, with terms confirmed per order. Always check the written terms in your own contract.

What we need to size your 315 ton gantry shear

Send material type and thickness, required daily capacity, available power supply, preferred blade length, site conditions and destination port. Photos or videos of your heaviest beams help us recommend the correct configuration.

Send them through our contact page and you will have a written quotation within 48 hours. If your numbers fit the 200 ton or a larger model better, we will tell you. You can browse the whole scrap metal shear range in the meantime.

Want cycle-time calculations or container loading details for your scrap mix? Compare full machine parameters on our 315 ton scrap metal shear page, review the hydraulic gantry shear series, or contact HUAXIN’s Tangshan engineering team with your feedstock photos and target daily tonnage.

Similar Posts

2 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *