400 Ton Gantry Shear – 400 Ton Scrap Metal Shear
This 400 ton gantry shear sizes a mixed ferrous intake of plate, H-beam, rebar, pipe and car bodies on one machine. The 400 ton scrap metal shear suits established yards that have outgrown a compact shear but do not need a mill-scale line.
- 400 t (4,000 kN), mild steel plate to 40 mm
- 3.5–5.5 t/h, 35–55 t per 10-hour day
- 45 kW, 2×37 kW or 2×45 kW
Why Choose Huaxin
- Real Factory, 30+ Years Manufacturing Experience
- 24/7 Technical Support
- Customized Solutions Available
- Installation & Training Support
Description
The 400 ton gantry shear (Q91-400) is for recycling companies that have outgrown a compact shear but do not need a mill-scale line. As a 400 ton scrap metal shear, its best job is sizing a mixed ferrous intake of plate, structural sections, rebar, pipe and car bodies on one machine. It cuts mild steel plate up to 40 mm continuously and turns out 35–55 t of sized scrap a day.
400 Ton Gantry Shear: Key Specifications
| Item | Q91-400 |
|---|---|
| Shearing force | 400 t (4,000 kN) |
| Blade length | 1,300 or 1,400 mm |
| Motor power | 45 kW, 2×37 kW or 2×45 kW |
| Output | 3.5–5.5 t/h, 35–55 t/day |
| Max plate (continuous, mild steel) | 40 mm |
| Feed box length | 5 / 5.5 / 6 m |
| Cycle time | 20–35 s per cut |
| Voltage | 230V / 380V / 400V / 415V / 440V / 480V, 50 or 60 Hz |
| Drive options | Electric, generator or diesel |
| Blade steel | M6V, H13, X45 or D2 tool steel, four-edge reversible |
| Control | PLC auto cycle, remote control, emergency stop |
| Certification | CE, ISO 9001 |
All tonnage numbers above are based on 10 working hours. Your real figure inside the 35–55 t band will depend on scrap density, how often the grab refills the box, and how much heavy section is in the mix.
One point confuses first-time buyers. The 400 t rating is blade force, not daily tonnage. On this machine, 4,000 kN of force produces 3.5–5.5 t/h of sized scrap, and the heavier the sections in the box, the closer you sit to the lower figure.
400 Ton Scrap Metal Shear Applications
This tonnage class handles a yard’s whole ferrous mix rather than one narrow stream. Plate above 30 mm, H-beam and heavy channel are daily work here, not occasional problems. For a closer look at beam work, see our note on cutting I-beam and H-beam on a 400 ton shear.
| Material | How this shear handles it |
|---|---|
| Mild steel plate | Up to 40 mm as continuous duty |
| H-beam and I-beam | Light to medium-heavy sections, fabrication offcuts included |
| Angle and channel | Light through heavy structural profiles |
| Rebar | Loose or bundled, from construction and demolition |
| Steel pipe | Single or bundled, within wall-thickness limits |
| Car bodies | Flattened or pre-treated shells |
| Shop and structural offcuts | Normal daily intake for an established yard |
| HMS 1 & 2 | Mixed in at a controlled share only, not as continuous duty |
Two jobs fall outside this machine. Continuous heavy melting steel belongs on a 630 t shear or larger. Plate thicker than 40 mm as routine feed also points to a bigger frame. Keep both in mind. Pushing either through a 400 t machine shortens blade life and slows every cycle that follows, so we write these limits into each quotation for the 400 t model alongside the force figure.
How the 400 Ton Scrap Metal Shear Works
- Loading comes first: an excavator grab or grapple crane drops the charge into the 5–6 m feed box.
- Side rams press the load together against the rear support, so loose rebar and pipe form a dense pack.
- The pusher advances the pack, and the moving blade comes down through it to cut a piece at the set length.
- Cut pieces fall out behind the machine while the blade returns for the next stroke.
Box length matters more at 400 t than on smaller models. A 6 m box takes long beam and pipe without pre-cutting by torch. That saves re-handling, and it keeps the grab feeding instead of waiting on a burner crew. Expect 20–35 seconds. Heavier sections sit at the slow end. Plan throughput on that range, never on the best stroke you see at the factory.
Set the cut length to your buyer. Short pieces suit furnace charge, while a mill or exporter loading containers may accept longer cuts. Agree the length before you order so the box and blade suit it. Trading yards that sell to several mills face this every week, and running a trading yard on a 400 ton shear shows how they handle it.
400 Ton Gantry Shear Build Quality and Hydraulics
Frame and blade seat
The gantry frame is stiffened and the cylinders are sized for structural sections rather than light offcuts. Welds on the Q355B gantry arch are ultrasonically tested in Tangshan, and the crosshead blade seat is CNC milled. Blade gap is shimmed to 0.3–0.5 mm across all four edges before the machine leaves.
Hydraulics and cycle
Hydraulic components and the valve block are matched to the 400 t cylinder load. Because the class carries plate over 30 mm with margin, cycle time holds through a full day. It does not drift as oil warms up. Blades come in M6V, H13, X45 or D2 tool steel, and each four-edge reversible blade gives four cutting edges before replacement.
PLC, remote and safety
A PLC runs the auto cycle. The operator works from a remote control, clear of the cutting zone, and an emergency stop reacts to abnormal hydraulic pressure.
Power options
Choose a single 45 kW motor, 2×37 kW or 2×45 kW to suit your mix and target tonnage. Supply can be grid, generator or diesel. Voltage is set to your switchboard before shipment. Tell us early. A yard on 480V at 60 Hz needs a different cabinet from one on 380V at 50 Hz, and HUAXIN builds the electrical side to that order rather than adapting it on site.
Choosing Between the 315 t, 400 t and 500 t Shears
| Item | Q91-315 | Q91-400 | Q91-500 |
|---|---|---|---|
| Shearing force | 315 t (3,150 kN) | 400 t (4,000 kN) | 500 t (5,000 kN) |
| Max plate (continuous) | 30 mm | 40 mm | 50 mm |
| Output | 2.5–4.5 t/h, 25–45 t/day | 3.5–5.5 t/h, 35–55 t/day | 4.5–6.0 t/h, 45–60 t/day |
| Feed box | 4.5 / 5 m | 5 / 5.5 / 6 m | 5 / 5.5 / 6 m |
| Bales | No | No | No |
Move up from 315 t once plate over 30 mm and heavy sections arrive daily. That is the usual trigger. A smaller machine fighting that feed burns blades and loses cycle time. Pick the 500 t model when demolition material with large, irregular, concrete-coated sections dominates, or when 50 mm plate is routine. Our guide to plate and section duty on a 400 ton scrap metal shear walks through the borderline cases.
Delivery, Commissioning and Support
Your quotation fixes the lead time and the packing method. Terms are EXW, FOB or CIF, with the complete machine declared under HS code 8462.3990. Frame, cylinder packages, power unit and electrical cabinet travel as separate heavy items, with a packing list and lifting plan matched to your receiving crane.
A field engineer can come to your yard to install the shear, commission it and train your operators. Before it ships, the shear goes through a load test in Tangshan, and the warranty runs 12 months. Spare blades, seals, valve parts and hoses are available, and cold-climate or tropical builds can be ordered.
Why Buy Direct From HUAXIN
You buy direct from the plant that builds the frame. Huaxin Co., Ltd. started building scrap metal equipment in 1989 and now runs two factories, one in Tangshan (Hebei) and one in Maanshan (Anhui), shipping to 30+ countries with more than 20 field engineers. Korean buyers also get local sales and after-sales service from our South Korea company.
400 Ton Gantry Shear FAQ
Is 400 t the right size for my yard?
Look at your daily tonnage and your thickest regular plate. If you size 35–55 t a day and plate up to 40 mm shows up regularly, a 400 ton gantry shear fits. Below 30 mm and under 45 t a day, the 315 t model costs less to buy and run.
Can a 400 ton scrap metal shear cut 50 mm plate?
Its continuous rating is 40 mm mild steel plate. If 50 mm plate is part of normal intake, choose the Q91-500, which is rated for 50 mm continuously and gives 45–60 t a day.
Which motor package should I choose?
A single 45 kW motor suits lighter mixes at the lower end of 3.5–5.5 t/h. The 2×37 kW and 2×45 kW packages keep cycles faster on heavier section work. Send your mix and we size it in the quotation.
Can it run without a grid connection?
Yes. Besides electric drive from 230V to 480V at 50 or 60 Hz, the 400 ton gantry shear can be supplied with a generator or diesel drive. That suits remote yards and sites with weak grid supply.
Does it handle car bodies and HMS?
Flattened or pre-treated car bodies are within its duty. 400 t is the smallest frame we offer for car-body work, for reasons set out in why 400 tons is the floor for car bodies. Mixed loads with some HMS 1 & 2 are fine too. Continuous heavy melting steel for steel mill charge is a 630 t job, and we will tell you before you order.
Compare the full Q91 hydraulic gantry shear series, or tell us your materials, daily tonnage and supply voltage and get a written Q91-400 quotation within 48 hours.
Additional information
| Machine Type | Hydraulic Scrap Metal Gantry Shear Machine |
|---|---|
| Model No. | Q91-400 |
| Shearing Force | 400Ton |
| Material Processed | Light, Medium and Heavy Scrap Metal |
| Application | Scrap Metal Recycling |
| Industry | Scrap Recycling (small to medium-scale) |
| Automation | Full Auto |
| Drive System | Hydraulic |
| Brand | HUAXIN |
| Origin | China |
| Certification | CE ISO9001 |










