
5-6 TPH Light Scrap Metal Crusher & Hammer Mill | Scrap Iron Crusher (PSX-280)
When a scrap stream shifts from thin 0.8 mm (0.03″) paint cans to folded washing machine cabinets, 2–3.5 mm (0.08″–0.14″) structural brackets, and unbolted car doors, a 200 kW rotor loses RPM on impact. Engineered by Huaxin Co., Ltd., the PSX-280 5-6 TPH scrap metal crusher retains the space-saving 1,400 mm (55″) chamber width while boosting main shaft power by 40% to 280 kW (375 HP) and upgrading hammer mass to 45–55 kg (99–121 lb) of ZGMn18Cr2Mo steel. Capable of running on a 400 kVA low-voltage (380V–440V) transformer, it produces 40–50 tons per day of 0.90–1.20 t/m³ furnace-ready steel nuggets through 35–70 mm (1.4″–2.8″) grate screens. What Else Can the PSX-280 Crush? Beyond loose light iron, this 280 kW hammer mill crushes sheet steel trimmings, 200L oil/paint drums, metal cans, aluminum profiles, cast-aluminum engine housings, and scrap electric motors on the exact same grate screen (e.g., 60 mm / 2.4″ or 70 mm / 2.8″) without swapping parts. Because its infeed opening is 1,400 mm (55″) wide, larger feedstocks—such as whole car shells, bulky refrigerators/washing machines, and long steel scrap—normally go through our alligator/gantry shear or dual-shaft shredder first before feeding the PSX-280. Running pre-sheared scrap increases output by 20%–30%, and feeding pre-shredded material raises capacity by 25%–40%.
Why Choose Huaxin
- Real Factory, 30+ Years Manufacturing Experience
- 24/7 Technical Support
- Customized Solutions Available
- Installation & Training Support
Description
Solving the Rotor Speed-Droop Problem in Mixed Light-Iron Yards
Two hammer mills can share the exact same 1,400 mm (55″) feed throat width and perform completely differently when fed double-walled steel. In mixed collector yards processing 40 to 50 tons per day, incoming scrap isn’t just thin roofing tin—it includes automotive hoods, tailgate stampings, water heater jackets, and 2–3.5 mm (0.08″–0.14″) laser-cut offcuts. When those folded seams hit the anvil bar, a lighter rotor slows down, forcing the PLC to stop the infeed conveyor repeatedly.
To eliminate those feeder pauses, Huaxin Co., Ltd. built the PSX-280 5-6 tph scrap metal crusher with a 280 kW (375 HP) main drive, a heavier Ø1,050 mm (Ø41.3″) disc rotor, and 45–55 kg (99–121 lb) ZGMn18Cr2Mo hammers. The resulting rotational inertia shears through multi-layer sheet stampings on the first pass while maintaining 580–630 RPM—even when fitted with tight 35–45 mm (1.4″–1.8″) induction-foundry screens.
What Else Can the PSX-280 Crush? Beyond loose light iron, this 280 kW hammer mill crushes sheet steel trimmings, 200L oil/paint drums, metal cans, aluminum profiles, cast-aluminum engine housings, and scrap electric motors on the exact same grate screen (e.g., 60 mm / 2.4″ or 70 mm / 2.8″) without swapping parts. Because its infeed opening is 1,400 mm (55″) wide, larger feedstocks—such as whole car shells, bulky refrigerators/washing machines, and long steel scrap—normally go through our Q43-250 Shear or HX-DS1000 Dual-Shaft Shredder first before feeding the PSX-280. Running pre-sheared scrap increases output by 20%–30%, and feeding pre-shredded material raises capacity by 25%–40%.
Mechanical & Electrical Comparison: PSX-280 vs. PSX-200
| Engineering Metric | PSX-280 (High-Torque 1,400 mm Class) | PSX-200 (Standard 1,400 mm Class) |
|---|---|---|
| Sustained Throughput | 5.0–6.5 TPH (40–52 TPD / 8h shift) | 3.0–5.0 TPH (24–40 TPD / 8h shift) |
| Infeed Throat Width | 1,400 mm (55″) with twin-cylinder pre-press roll | 1,400 mm (55″) with standard pre-press roll |
| Main Motor & Voltage | 280 kW (375 HP) | 380V–440V LV (or 6kV/10kV HV optional) | 200 kW (270 HP) | 380V–440V LV |
| Single Hammer Weight | 45–55 kg (99–121 lb) ZGMn18Cr2Mo alloy | 35–45 kg (77–99 lb) ZGMn18Cr2Mo alloy |
| Max Sheet Thickness | Up to 3.5 mm (0.14″) mild steel panels & light profiles | Up to 2.5–3.0 mm (0.10″–0.12″) thin tin & drums |
| Standard Grate Apertures | 35–70 mm (1.4″–2.8″) | Output density 0.90–1.20 t/m³ | 30–60 mm (1.2″–2.4″) | Output density 0.85–1.15 t/m³ |
| Recommended Transformer | 400 kVA (with soft-starter / VFD cabinet) | 315 kVA |
Maximum Kilowatts Before Stepping Into High-Voltage Grid Permits
In many industrial zones across Southeast Asia, the Middle East, Latin America, and Eastern Europe, upgrading a yard’s utility connection from 400V low-voltage to 6.6 kV or 10 kV high-voltage costs $35,000–$70,000 in transformer and switchgear permits alone. At 280 kW (plus ~38 kW for the apron feeder, vibrating pan, magnetic separator, and hydraulics), the PSX-280 is the largest hammer mill in the industry that still runs reliably on a 400V/415V/440V low-voltage grid using a heavy-duty thyristor soft-starter or VFD.
Chamber Armor, Anvil Geometry & Shift-Friendly Maintenance
- Stationary Shear Anvil & Baffle Liners: The entry throat features a replaceable alloy anvil beam set at a tight clearance to the hammer tips, shearing wide automotive hoods and refrigerator doors cleanly rather than dragging them intact around the rotor. Interior walls are lined with 40 mm (1.6″) ZGMn13Cr2 and NM450 wear plates secured by recessed countersunk bolts.
- 3-Minute Hydraulic Clam-Shell Hood & Pin Puller: Two heavy-duty hydraulic cylinders open the upper housing past 75 degrees for overhead crane access. A side-mounted hydraulic pin extractor pushes the 42CrMo hinge pins out laterally so two operators can rotate all 16 hammers between shifts.
- Downstream Sorting Purity: Discharged steel pellets drop onto a spring-isolated vibrating pan feeder (preventing hot metal from burning rubber belts) before passing beneath a permanent NdFeB magnetic drum that separates clean foundry charge from plastic fluff and non-ferrous Zorba.
Where the PSX-280 Fits in Your Yard Lineup
- Smaller 380V Drum Option: PSX-200 (3–5 TPH, 200 kW) for light drums and thin stamping skeletons.
- Wider 1,600 mm (63″) Throat for Bulky Appliances: PSX-315 (6–8 TPH, 315 kW) or PSX-400 (8–12 TPH, 400 kW).
- Upstream Pre-Shredding for Unsorted Bales: Pair with our HX-DS1200 Dual-Shaft Shredder (5–15 TPH) or browse the Full PSX Crusher Catalog.
Technical Q&A: PSX-280 (5–6 TPH) Light-Iron Hammer Mill
1. Can I feed whole passenger car shells into the PSX-280?
Not whole unflattened cars—a standard passenger car shell is 1,700–1,850 mm (67″–73″) wide, which will bridge across a 1,400 mm (55″) throat. However, if you pre-cut car bodies lengthwise on a Q91 Hydraulic Gantry Shear or pre-shred them in a dual-shaft shredder, the PSX-280 crushes the resulting panels effortlessly. For direct flattened car shells, start at the PSX-560 (1,800 mm / 71″ throat).
2. What is the power consumption per ton of crushed steel?
In continuous operation on mixed 1–3 mm (0.04″–0.12″) sheet iron and appliance shells using a 50 mm (2.0″) grate screen, the PSX-280 line consumes 42–52 kWh per metric ton of finished clean steel nuggets.
Get Your PSX-280 Plant Drawing & Price List: Reach out to Sales Manager Leon Li at Huaxin Co., Ltd. ([email protected] | WhatsApp +86 159 0036 3543 | Online Inquiry Form) with photos of your scrap feedstock for a custom configuration within 24 hours.
Additional information
| Machine Type | Scrap Metal Crusher / Hammer Mill Shredder Line (PSX Series) |
|---|---|
| Model | PSX-280 (PSX280) |
| Hourly Capacity | 5-6 TPH (40-50 tons/day (8-hour shift)) |
| Inlet Width | 1,400 mm |
| Main Motor Power | 280 kW |
| Voltage System | 380V / 400V / 415V / 440V Low-Voltage (or 6kV/10kV Optional) |
| Output Fragment Size | 35-70 mm standard (30-120 mm customizable) |
| Crushed Steel Density | 0.90-1.20 t/m³ |
| Hammer Material | Mn18Cr2 High-Manganese Cast Steel (45-55 kg per hammerhead (Mn18Cr2)) |
| Maintenance System | Hydraulic Hammer Pin Extractor + Hydraulic Casing Tilt |
| Standard Line Equipment | VFD Chain-Plate Conveyor, Hydraulic Pre-Press Roller, Hammer Mill, Vibrating Feeder, Permanent Magnet Drum, Discharge Belts, PLC Control |
| Optional Systems | Cyclone + Pulse-Jet Baghouse Dust Collector, Cooling Spray, Air Classifier, Eddy-Current Non-Ferrous Sorter |
| Warranty & Delivery | 1-Year Warranty, Within 45 Days After Payment, CE & ISO 9001 |
