630 Ton Gantry Shear – 630 Ton Scrap Metal Shear
The 630 ton gantry shear (Q91-630) is built for steel-mill yards and regional scrap hubs that cut HMS 1 & 2 all day. As a 630 ton scrap metal shear, its 1,500 or 1,600 mm blade and 6–7 m box take long beams and plate.
- 6,300 kN force, 60 mm mild steel plate continuous
- 6.0–8.0 t/h, 60–80 t per 10-hour day
- 2×45 kW or 3×45 kW, 50/60 Hz
Why Choose Huaxin
- Real Factory, 30+ Years Manufacturing Experience
- 24/7 Technical Support
- Customized Solutions Available
- Installation & Training Support
Description
The Q91-630 is a 630 ton gantry shear for steel-mill scrap yards and regional ferrous hubs that cut heavy melting steel all day. It delivers 6,300 kN through a 1,500 or 1,600 mm blade and turns out 60–80 t of furnace-ready HMS 1 & 2 in a 10-hour day. For this 630 ton scrap metal shear, plate up to 60 mm thick is continuous duty.
630 Ton Gantry Shear: Key Specifications
| Item | Q91-630 |
|---|---|
| Shearing force | 630 t (6,300 kN) |
| Blade length | 1,500 or 1,600 mm |
| Motor power | 2×45 kW or 3×45 kW |
| Output | 6.0–8.0 t/h, 60–80 t/day |
| Max plate (continuous, mild steel) | 60 mm |
| Feed box length | 6 / 6.5 / 7 m |
| Cycle time | 20–35 s |
| Voltage | 230V / 380V / 400V / 415V / 440V / 480V, 50 or 60 Hz |
| Drive options | Electric, generator or diesel |
| Blade steel | M6V, H13, X45 or D2 tool steel, four-edge reversible |
| Control | PLC auto cycle, remote control, emergency stop |
| Certification | CE, ISO 9001 |
Daily tonnage is based on 10 working hours. A yard feeding mostly rebar bundles and medium sections, with a grapple refilling the box between strokes, runs near 80 t; heavy plate cut by plate pulls it toward 60 t.
630 Ton Scrap Metal Shear Applications
This is the first size in the Q91 range that we rate for non-stop HMS 1 & 2 rather than mixed light and medium scrap. Smaller frames can cut the same pieces. Not for ten hours, though. At 630 t the machine carries enough cylinder force, frame mass and oil cooling to hold full cutting pressure through long runs of dense charge without slowing in the afternoon.
| Material | How the shear handles it |
|---|---|
| HMS 1 & 2 | Core duty, full-day continuous shearing to furnace length |
| Mild steel plate | Up to 60 mm, continuous |
| H-beam, I-beam, channel, angle | Light to heavy sections from bridge and plant dismantling |
| Rebar | Loose or bundled construction rebar |
| Pipe and tube | Thick-wall single pipes or bundled tubing |
| Car bodies and truck frames | Flattened shells, chassis rails, commercial truck frames |
| Mill returns | Steelworks crops, fabrication offcuts, foundry returns |
Keep out compacted scrap bales and plate thicker than 60 mm as daily feed. Both belong on 1,000 t. Light sheet, appliances and loose car shells also earn more through a shredder than through a scrap shear. For a longer discussion of why this tonnage marks the move to continuous melt-shop feed, read why 630 tons is the HMS watershed.
How the 630 Ton Scrap Metal Shear Works
- A material-handler grab or magnet crane drops long HMS and structural steel into the 6–7 m open box.
- Side cylinders close and press wide scrap into a dense log. A vertical hold-down cylinder then pins the log in front of the blade.
- The main cylinder group drives the upper slide down, and the scrap is cut against the fixed lower blade.
- As the blade lifts, the rear pusher advances the log by the preset length, and cut pieces fall onto a conveyor or into a pit.
Box length matters here. A 7 m box lets a crane drop full-length beams and rail-sized sections straight in without torch prep, which is where most of the labour saving on a heavy yard comes from. Size it to your crane reach.
Heavy-Duty Build of the 630 Ton Gantry Shear
Frame and slide
Heavy plate cutting at 6,300 kN pushes sideways on the frame with every stroke. The gantry uprights and crossbeam are fabricated from thick Q355B plate with full-penetration submerged-arc welds, then stress-relief annealed in a furnace. The upper slide runs in machined, self-lubricating bronze guides to hold blade clearance under off-centre loads. Replaceable NM400 liners protect the box walls from sliding HMS.
Hydraulics and cycle time
Two or three 45 kW motor-pump groups feed high-pressure axial piston pumps through cartridge valve manifolds. Rebar bundles and light sections cycle near 20 s. Solid 60 mm plate and dense HMS need the full stroke, closer to 30–35 s. We plan your hourly output on the slower heavy-load cycle plus crane time. How that adds up across a day is set out in planning two-shift output on a 630 ton shear. An oversized oil tank and an air-cooled or water-cooled heat exchanger keep oil viscosity steady through hot afternoons.
PLC, remote and safety
A Siemens or Schneider PLC runs the automatic cut cycle and stores the cut length. With the wireless remote, the crane driver can pause, advance or stop the shear from the cab. Emergency stops sit on the console as well.
Power options
Motors start one after another. That cuts peak current on your yard transformer, which matters when the shear shares a supply with cranes, a baler or mill equipment. The cabinet is wired to your local three-phase voltage before the factory test. Remote sites can run the 630 t model on a diesel generator instead of the grid.
Choosing a 630 Ton Gantry Shear Over the 500 or 1000 t Models
| Item | Q91-500 | Q91-630 | Q91-1000 |
|---|---|---|---|
| Shearing force | 500 t (5,000 kN) | 630 t (6,300 kN) | 1,000 t (10,000 kN) |
| Max plate (continuous) | 50 mm | 60 mm | 100 mm |
| Output | 4.5–6.0 t/h, 45–60 t/day | 6.0–8.0 t/h, 60–80 t/day | 10–12 t/h, 100–120 t/day |
| Feed box | 5 / 5.5 / 6 m | 6 / 6.5 / 7 m | 6 / 6.5 / 7 m |
| Cuts bales | No | No | Yes |
Below about 50 t a day, or with feed that is mostly sections under 50 mm, the Q91-500 pays back faster on less power. Pick the 630 ton gantry shear once HMS is the main stream and you need 60 t or more every day. If baled scrap is part of the intake, or you are planning beyond 80 t a day, go straight to the Q91-1000. The full range sits in our Q91 hydraulic gantry shear series.
Installing a 630 t Gantry Shear
A complete 630 t machine is too heavy to ship in one piece. It bolts together from modules (gantry, box sections, cylinders, power pack and console) that travel in 40HQ and flat-rack containers, with a packing list giving component weights and rigging drawings. Your quotation fixes the lead time and packing method. Terms are EXW, FOB or CIF. Customs code for the complete machine is HS 8462.3990.
After the order, our engineers issue civil foundation drawings and cable layouts. Your contractor can pour the pad while the shear is at sea. HUAXIN field engineers then supervise assembly, set hydraulic pressures and train your crew on loading, PLC cut lengths and daily lubrication. Each quotation lists recommended spare blades, seal kits and valves. Before shipment the shear runs a factory load test, and the warranty covers 12 months. Cold-climate and tropical builds are available.
Why Buy This 630 t Shear From HUAXIN
Since 1989 Huaxin Co., Ltd. has made scrap metal machinery, today in two plants: Tangshan, Hebei and Maanshan, Anhui. Our South Korean sales and service company, together with 20+ field engineers for installation and training, looks after shears exported to 30+ countries. CE and ISO 9001 apply to every Q91 model.
630 Ton Gantry Shear FAQ
When does a yard need 630 t rather than 500 t?
Check two numbers. If you process 60–80 t a day and most of it is heavy melting steel or plate near 50–60 mm, this machine fits. Under 50 t a day with lighter sections, the 500 t model is the better buy.
What is the thickest plate this 630 ton scrap metal shear cuts every day?
Mild steel plate up to 60 mm is rated continuous duty. We do not quote a higher peak figure. If thicker plate arrives daily, or you cut ship plate in volume, size up to the Q91-1000, which is rated for 100 mm.
What power supply does the 630 t model need?
Choose 2×45 kW or 3×45 kW, wired for any of 230V, 380V, 400V, 415V, 440V or 480V at 50 or 60 Hz, with motors started in sequence to limit inrush current. On sites without grid capacity, a diesel generator set can drive the machine; we size it to your chosen motor package.
Can a 630 ton scrap metal shear cut railway rail?
Rail is a common feed for this class, and the 6–7 m box takes long lengths. Blade choice and cut position matter more on rail than on HMS. Our rail cutting notes for the 630 t shear cover both.
What foundation does it need?
A reinforced concrete pad built to our civil drawings, which we send once the order is confirmed. Pad size depends on the box length you choose, 6, 6.5 or 7 m. It can be poured during transit. Assembly then starts on arrival.
Send your scrap mix, daily tonnage and site power through our contact page for a written Q91-630 quotation within 48 hours.
Additional information
| Machine Type | Hydraulic Scrap Metal Gantry Shear Machine |
|---|---|
| Model No. | Q91-630 |
| Shearing Force | 630Ton |
| Material Processed | Light, Medium and Heavy Scrap Metal |
| Application | Scrap Metal Recycling |
| Industry | Scrap Recycling (medium-scale) |
| Automation | Full Auto |
| Drive System | Hydraulic |
| Brand | HUAXIN |
| Origin | China |
| Certification | CE ISO9001 |







