800 Ton Scrap Metal Baler Machine | Y81K-800 Hydraulic Baling Press

The Y81K-800 800 ton scrap metal baler is a high-density, tri-motor (3×55 kW = 165 kW) hydraulic baling press applying 800×2 tons (1,600T combined) of main-cylinder force inside a 3500×3000×1300 mm (138″×118″×51″) chamber. Engineered for melt shops and heavy ferrous processors that demand maximum bale density in a compact cross-section, it compresses heavy mixed ferrous, HMS 1 & 2, plate trimmings, and structural steel into 600×600 mm (24″×24″) blocks weighing 800-1,400 kg at 10 to 18 tons per hour.

  • 800×2 Ton Force on a 600×600 mm (24″×24″) Bale: Highest specific ram face pressure in the mid-large class for ultra-dense 1.4-ton blocks.
  • 165 kW Tri-Pump Hydraulic Station: Three 55 kW motors and axial piston pumps deliver fast cycle times under continuous 3-shift loads.
  • 3500×3000×1300 mm (138″×118″×51″) Armored Box: Lined throughout with replaceable Hardox 500 wear plates and top lid shearing blades.
  • Side Push-Out Mill Discharge: Siemens PLC automation with wireless grapple remote and fault diagnostics.

Huaxin Co., Ltd. Factory Direct: CE & ISO 9001 certified. Request your Y81K-800 factory quote & technical datasheet →

Why Choose Huaxin

  • Check Mark Real Factory, 30+ Years Manufacturing Experience
  • Check Mark 24/7 Technical Support
  • Check Mark Customized Solutions Available
  • Check Mark Installation & Training Support

Description

800 Ton Scrap Metal Baler for Sale (Y81K-800 High-Density 165 kW Mill Press)

Why do specialized steel mills and high-grade scrap exporters choose the Y81K-800 800 ton scrap metal baler over a 630-ton unit when both share a 3500×3000×1300 mm (138″×118″×51″) chamber? Look at two numbers: 800×2 tons (1,600 tons combined) of main-cylinder thrust concentrated onto a 600×600 mm (24″×24″) bale face, driven by a 3×55 kW (165 kW) three-pump hydraulic power pack.

Concentrating 1,600 tons of force onto a 600×600 mm (24″×24″) cross-section generates extreme specific compression pressure—packing up to 1,400 kg of heavy HMS 1 & 2, structural offcuts, and alloy scrap into a compact block that melts faster in an electric arc furnace with minimal oxidation loss.

At the same time, stepping up from two 55 kW motors (110 kW on the 630T) to three 55 kW motors (165 kW total) on this 800 ton scrap metal baler for sale increases hydraulic oil flow by 50%. Even with larger main cylinders, the Y81K-800 completes full compression and side push-out cycles faster, sustaining 10 to 18 tons per hour across continuous three-shift operations.

Who Specifies the High-Density Y81K-800 Class?

  • Specialty Steelworks & EAF Melt Shops: Plants whose furnace charging doors or conveyor chutes require a strict 600×600 mm (24″×24″) cross-section but want 800-1,400 kg packet weight.
  • High-Volume Ferrous Processors (90-150 Tons/Day): Yards processing heavy industrial scrap, shipbuilding offcuts, railway dismantling steel, and HMS 1 & 2.
  • Model Comparison: Compare one tier down at the 630 Ton Scrap Metal Baler (Y81K-630), or step up to a deeper 1,400 mm (55″) box and 2,000 tons of combined force on our 1000 Ton Scrap Metal Baler (Y81K-1000).

Technical Specifications – Y81K-800 Hydraulic Baling Press

Specification Parameter Y81K-800 (800T Class)
Model Designation Y81K-800
Main cylinder force 800×2 ton
Chamber size 3500×3000×1300
Bale size 600×600
Bale weight 1400 kg
Motor 3×55 kW
Duty rating Continuous three-shift duty

Chamber Dimensions & Bale Weight Configurations (Y81K-800)

Compare the verified compression chamber dimensions (3,500×3,000×1,300 mm (138″×118″×51″)) and bale cross-sections (600×600 mm (24″×24″) or 700×700 mm (28″×28″) ultra-dense bale) for the 800 Ton Mill-Duty Scrap Metal Baler (Y81K-800) below to match your crane loading span and smelter contract:

Chamber Dimensions (L×W×H mm) Bale Cross-Section (mm) Typical Bale Weight (kg)
3500×3000×1300 600×600 800-1400

Material Feed Suitability Matrix (Y81K-800)

Material Processing Notes & Suitability
Heavy mixed ferrous routine duty for this class
HMS 1 & 2 processed at the quoted output
Industrials Primary recommended feed for this tonnage class

165 kW Tri-Pump Hydraulic Architecture & Heavy Structural Engineering

Running a Y81K-800 hydraulic baling press three shifts a day requires redundancy and thermal control. The Y81K-800 power station divides the 165 kW load across three independent 55 kW motor-pump groups controlled by a Siemens PLC. During startup, motors engage sequentially to eliminate grid voltage spikes. If one pump group is ever isolated for routine filter or seal servicing, the machine can continue operating at reduced speed on the remaining two pumps—preventing unscheduled plant shutdowns.

Hardox 500 Liner System, Forged Cylinders & Line Pairing

The main cylinders are honed from thick-wall seamless alloy forging barrels with induction-hardened 42CrMo4 piston rods. Inside the 3500×3000×1300 mm (138″×118″×51″) chamber, bolted Hardox 500 wear liners protect every sliding surface. Many 100+ TPD plants pair the Y81K-800 with a heavy gantry shear—read our engineering guide on Scrap Metal Recycling Line Design: Shear to Bale.

Why 1,600 Tons on a 600×600 mm (24″×24″) Face Maximizes EAF Melt Efficiency

In electric arc furnace (EAF) steelmaking, loosely packed bales trap air pockets that oxidize molten steel, increase slag volume, and cause electrode breakage when charges cave in. The Y81K-800 solves this by channeling 800×2 tons (1,600 tons combined) of twin-cylinder force inside a 3500×3000×1300 mm (138″×118″×51″) chamber down to a compact 600×600 mm (24″×24″) cross-section. The resulting 444 kg/cm² specific ram pressure compacts heavy mixed ferrous scrap and HMS 1 & 2 into 800-1,400 kg blocks with metallurgical density exceeding 1.6-1.9 t/m³.

165 kW Tri-Motor Hydraulic Station & N+1 Uptime Design

  • Three Independent 55 kW Pump Groups: Delivers 50% more oil flow than dual-motor 110 kW presses while providing N+1 operational backup if one pump is isolated for servicing.
  • Forged Cylinder Barrels: Main and side cylinders are machined from thick-walled forged 27SiMn / 45# alloy steel barrels with induction-hardened 42CrMo4 piston rods.
  • PLC Fault Diagnostics: Touchscreen HMI displays real-time system pressure, oil temperature, filter differential pressure, and limit-switch status for fast troubleshooting.

Frequently Asked Questions (FAQ) – Y81K-800

Why does the Y81K-800 produce a 600×600 mm (24″×24″) bale instead of an 800×800 mm (32″×32″) bale?

By focusing 800×2 tons (1,600T combined) onto a 600×600 mm (24″×24″) cross-section rather than spreading it over a wider face, the Y81K-800 achieves substantially higher bale density (800-1,400 kg per bale), reducing air voids inside the EAF furnace and maximizing container weight limits.

Can the Y81K-800 run if one of the three 55 kW motors is offline for maintenance?

Yes. The three 55 kW motor-pump units are plumbed in parallel with check-valve isolation, allowing the press to complete full-pressure cycles at two-thirds speed if one pump is paused for maintenance.

What scrap thickness can the Y81K-800 compress?

It routinely compresses HMS 1 & 2, structural steel sections, plate offcuts up to 12-15 mm (0.5-0.6″), heavy pipe, and flattened vehicle frames.

What electrical supply and foundation are required for the Y81K-800?

The 165 kW (3×55 kW) station is built for 380V/415V/440V/480V (50/60 Hz) or high-voltage supply to order, requiring a ~250 kVA transformer capacity and a reinforced concrete foundation built to our certified drawings.

How long does manufacturing and load testing take?

Manufacturing and 72-hour continuous pressure/load testing at our Tangshan factory take 45-60 days. Third-party inspection (SGS/BV) or live video verification is included before shipment.

Tangshan Factory Inspection, Civil Readiness & Buyer Resources (Y81K-800)

Built directly by Huaxin Co., Ltd. (founded 1989), the Y81K-800 is stress-relieved, CNC-machined, and pressure-tested for 72 hours under full hydraulic load prior to shipment. Engineered for 800T industrial duty with CE & ISO 9001 certification, foundation/electrical schematics, and 24h quotation turnaround.

Matched Buyer Search Configurations: Covers industrial requirements for a 800 ton scrap metal baler for sale, Y81K-800 800×2 ton high-density 600x600mm (24″x24″) scrap baler, 165 kW three-motor heavy ferrous baling press, 1400 kg furnace charge scrap metal baler machine, continuous three-shift industrial steel baler from China, complete with itemized FOB/CIF quotes, PLC electrical schematics, and one-year structural warranty.

Related Technical & Line-Planning Guides

Request a Y81K-800 Factory Quotation & 2D Foundation Layout: Email Huaxin Co., Ltd. Sales Manager Leon Li at [email protected], message WhatsApp +86 159 0036 3543, or submit your feedstock details via our Contact Page to receive FOB/CIF pricing and 2D CAD drawings for the 800 Ton Mill-Duty Scrap Metal Baler (Y81K-800) (8,000 kN (2×400T twin main cylinders, 444 kg/cm²), 3×55 kW (165 kW N+1 redundant)) within 24 hours.

Additional information

Machine Name

Hydraulic Scrap Metal Baler

Power

800 Ton

Model Number

Y81K-800

Feeding Tank

3500×3000×1300 mm

Bale Size

600×600 mm

Bale Weight

1400 kg per bale (estimated, varies with material)

Motor Power

3×55 kW

Control System

Manual, semi-auto & full PLC automatic

Application for

heavy mixed ferrous, HMS 1&2, industrials

Power Sources

Electric, 3-phase, 380V/50Hz, 400V/50Hz or 415V/50Hz (customized voltage available); diesel engine optional

Get A Free Quote

    Your Name *

    Your Email *

    Your Phone / WhatsApp *

    Machine Application *

    Raw Material

    Output Rate per Hour


    Ton / Hour

    Power Supply

    Subject

    Message

    OEM Replacement Blades, Wear Liners, Sub-Zero (-40°C) Packages & Customs HS Codes

    In addition to brand-new turnkey machinery backed by a 12-month factory warranty, HUAXIN manufactures and exports direct-fit OEM replacement blades, wear plates, high-manganese castings, and hydraulic cylinder assemblies—including custom-machined replacement blades built to your exact engineering drawings or sample dimensions. Standard wear parts ship within 5 business days, and custom-forged orders ship within a maximum of 20 days.

    Item / Component Category Export Customs HS Code Metallurgy & Engineering Options Lead Time & Pricing Factors
    Complete Host Machine 8462.6190 / 8479.8190 Hydraulic Scrap Metal Baling Press / Triple-Compression Metal Baler (CE & ISO9001 Certified, 100% New with Warranty) 30-55 Days · EXW / FOB Tianjin / CIF / CFR / DDP
    Primary Cutting / Crushing Wear Parts 8208.1000 / 7326.9019 Hardox 450 / Hardox 500 / NM500 Chamber Wear Liners & Lid Trim Blades · Precision ground to ±0.02 mm tolerance 5 Days (Stock) / ≤20 Days (Custom) · Priced by steel grade, dimensions & order qty
    Sub-Zero / Arctic Climate Package (-20°C to -40°C) 8208.1000 / 7326.9019 / 8412.2100 Deep cryogenic-treated impact blades (anti-fracture at -40°C), Parker low-temperature cylinder seals & oil tank heaters Custom engineered for Russia, Canada, Nordic & Northern US yards · Contact for Quote
    Hydraulic Cylinders & Seal Kits 8412.2100 Forged 42CrMo piston rods with 0.06-0.08 mm hard chrome plating + genuine Parker / Hallite / NOK seal kits Seal Kits ≤5 Days / Cylinders ≤20 Days · Consolidated container or air express

    How Spare Parts Pricing is Calculated: Replacement blade, hammer, liner, and cylinder prices depend on (1) alloy grade requirement (M6V/H13/X45/D2 vs. Forged H13 vs. Cryogenic Sub-Zero Grade), (2) exact drawing dimensions & bolt pattern, (3) ambient operating temperature (-20°C to -40°C Arctic toughness vs. +50°C desert cooling), and (4) trade terms (EXW, FOB, CIF, or bundled duty-free inside your new machine container). Send us your machine model or blade drawing for a same-day factory quote →

    Get Quote